| |
| Name of Products | GFP-Human Lung Airway Smooth Muscle Cells (GFP-HLAWSMCs) |
| Catalogue Number | cAP-0121GFP |
| Product Format | Frozen Vial |
| Cell Number | > 5x10[5] cells/vial |
| HLAWSMCs (cAP-0121) are isolated from human normal lung small airway tissues. GFP-HLAWSMCs are selected from puromycin resistant HLAWSMCs, after infected with Lentivirus expressing GFP and the cells are shipped in frozen vials (provided @ passage 3).The Smooth Muscle Cells (SMCs) Growth Medium (contains FBS and Growth factor supplements, cAP-24) is recommended for cell culture and these cells have a minimum average population doubling levels > 8 (2-3 passages) when cultured following the detailed protocol described below). |
| |
| 1. | Alpha-Vascular SMA > 98% positive by immunofluorescence |
| 2. | VE-Cadherin < 1% positive by immunofluorescence |
| 3. | HLAWSMCs are negative for HIV-1, HBV, HCV, and mycoplasma |
| Cells are offered for Research Use Only. |
| Frozen Vials in a Dry Ice Package. |
| When you receive the dry ice package with cells in frozen vials, transfer the frozen vials of cells into a -80C freezer for short period storage or a liquid nitrogen tank for long- term storage. |
| |
| A) | Pre-coating of T25 flasks- Add 2ml each Quick Coating Solution (cAP-01) into a T25 flask to cover the whole surface of the flask, 5 mins later, remove excessive coating solution by aspiration and the flask is ready to be used (although solution containing other extracellular matrix, i.e. gelatin, collagen, and fibronectin, can be used, make sure to optimize the conditions in advance). |
| B) | Thaw the frozen cell vial in a 37C water bath first, and then transfer the cells into the pre-coated T25 flask with 10ml of cAP-24 medium, cells usually become confluent with 1-2 days and ready to be passaged. |
| C) | To passage the cells, rinse the cells in a T25 flask with 5ml HBSS (RT) twice; then add 2ml Trypsin/EDTA (RT) (cAP-23) into one T25 flask; gently dispose the excessive Trypsin/EDTA solution within 20 seconds by aspiration. |
| D) | Leave the T25 flask with the cells at RT or 37C for 1 min (most cells usually will detach from the surface within 1-2 mins; or monitor the cells under a microscope until most of cells become rounded up, and then gently tap the flask against the bench surface, and the cells will move on the surface of the flask when monitoring under microscope. |
| E) | Add 5ml Trypsin Neutralization Buffer and spin down the cells with 800RPM centrifugation for 5 mins. |
| G) | Re-suspend the cell pellet with 10 or 15ml cAP-09 medium and transfer 5 ml each into 2 or 3 pre-coated T25 flasks (for 1/2 to 1/3 subculture ratio). |
| H) | Change medium every 2 or 3days and the cells usually become confluent within 7 days (when split at a 1/3 ratio). |
| I) | To prepare quiescent cells, when cells are nearly confluent, replace cAP-24 with SMCs (SMCS) Basal Medium (cAP-24B) containing 0.5%FBS for about 8-12hrs before your experiments. |
| |
| Quick Coating Solution | cAP-01 |
| Pericyte Growth Medium | cAP-09 |
| Pericyte Growth Medium (Super rich formulation) | cAP-09B |
| Pericyte Basal Medium | cAP-09C |
| HBSS w/o Ca2+, Mg2+ | cAP-11 |
| Cell Freezing Solution (FBS) | cAP-22 |
| Cell Freezing Solution (Non-FBS) | cAP-22B |
| Trypsin/EDTA Solution | cAP-23 |
| Trypsin Neutralization Solution | cAP-28 |
| ITS (100x) | cAP-26 |
| L-Glutamine-MAXIMUM (100x) | cAP-27 |
| Human Plasma Fibronectin Solution | cAP-42 |
| Handling human tissue-derived products is potentially bio-hazardous, despite tested negative for HIV, HBV and HCV DNA; nonetheless, proper precautions must be taken to avoid inadvertent exposure. |
For customers using our primary cell products, we strongly advise you using our own medium, although similar cell growth medium can be purchased and used for our primary cell products. |
The quality of cells, in term of their growth features stated in our datasheets, will not be guaranteed if NON-ANGIO-PROTEOMIE's Cell Growth Medium is used. |
Due to the sensitive nature of primary cells and cell lines, all quality related issues about the cells products must be reported back to us within ONE month period after receiving the products, no quality warranty (i.e. replacement of cells) will be provided after the ONE-Month period. Thank you for your understanding. |
